Spinner: Difference between revisions
Wigsplitta (talk | contribs) No edit summary |
Wigsplitta (talk | contribs) No edit summary |
||
| Line 64: | Line 64: | ||
|} | |} | ||
== | == Pinouts == | ||
===Seimitsu LS-29=== | |||
Pin1: X1<br> | Pin1: X1<br> | ||
Pin2: +5 Volts<br> | Pin2: +5 Volts<br> | ||
Pin3: GND<br> | Pin3: GND<br> | ||
Pin4: X2 | Pin4: X2<ref>[http://www.neo-geo.com/forums/showthread.php?199615-Seimitsu-LS-29-connectors&p=2774116 Neo-Geo Forums]</ref><br> | ||
===Taito 4 Pin=== | |||
[[File:Taito_Spinner_4pin_Pinout.jpg|150px|thumb|right]] | [[File:Taito_Spinner_4pin_Pinout.jpg|150px|thumb|right]] | ||
Pin1: Right<br> | Pin1: Right<br> | ||
Pin2: +5 Volts<br> | Pin2: +5 Volts<br> | ||
Pin3: GND<br> | Pin3: GND<br> | ||
Pin4: Left<br> | Pin4: Left<ref>[https://forums.arcade-museum.com/threads/taito-spinner-6-pin-wiring.494679 KLOV Arkanoid Manual]</ref><br> | ||
===Taito 6 Pin=== | |||
== | |||
Pin1: +5 Volts<br> | Pin1: +5 Volts<br> | ||
Pin2: +5 Volts<br> | Pin2: +5 Volts<br> | ||
| Line 89: | Line 91: | ||
Pin4: GND<br> | Pin4: GND<br> | ||
Pin5: Left<br> | Pin5: Left<br> | ||
Pin6: Right<br> | Pin6: Right<ref>[https://forums.arcade-museum.com/threads/taito-spinner-6-pin-wiring.494679 KLOV forums]</ref><br> | ||
== | ===Ultimarc to USB Interface=== | ||
[[File:Ultimarc_Spinner_USB.jpg|150px|thumb|right]] | [[File:Ultimarc_Spinner_USB.jpg|150px|thumb|right]] | ||
Pin1: +5 Volts (Brown)<br> | Pin1: +5 Volts (Brown)<br> | ||
| Line 98: | Line 100: | ||
Pin3: GND (White)<br> | Pin3: GND (White)<br> | ||
Pin4: X1 (Yellow)<br> | Pin4: X1 (Yellow)<br> | ||
Pin5: Empty<br> | Pin5: Empty<ref>[https://www.ultimarc.com/trackballs-and-spinners/spinners/spintrak Ultimarc]</ref><br> | ||
== References == | == References == | ||
Revision as of 20:20, 22 May 2024
A Spinner is a type of control interface used in several arcade titles. To install a spinner, depending on the type, you either need to remove the knob and install it like a joystick, or completely disassemble the spinner and remove the c-ring to release the shaft, and then re-build the spinner around the control panel. When installing the spinner, make sure the encoder wheel doesn't touch the optical switches when in upright position, as this will cause resistance on the wheel and make the spinner difficult to use.
Gallery
Taito
-
Purple 4 gear flat plate -
Red 4 gear 'S' plate -
-
-
4 pin Opto pcb -
4 pin Opto pcb -
6 pin Opto pcb -
6 pin Opto pcb
-
Wico Opto pcb -
Wico Opto pcb -
Repro Opto pcb -
Repro Opto pcb
Capcom
-
Repro Spinner and CP setup
Ultimarc
Compatible Games
| Title | Setup |
|---|---|
| Arkanoid | Left and Right bind to L/R on the harness |
| Arkanoid - Revenge of DOH | Left and Right bind to L/R on the harness |
| Arkanoid Returns | Left and Right bind to L/R on the harness |
| Block Block | Connectors on official Capcom JAMMA adapter |
| Cameltry | Left and Right bind to L/R on the harness |
| Puzz Loop | CN6 pinout 1. +5VDC 2. 1p 3. 2p 4. - 5. - 6. 1p 7. 2p 8. GND [1] |
| Puzz Loop 2 | Connectors on official Capcom JAMMA adapter |
Pinouts
Seimitsu LS-29
Pin1: X1
Pin2: +5 Volts
Pin3: GND
Pin4: X2[2]
Taito 4 Pin
Pin1: Right
Pin2: +5 Volts
Pin3: GND
Pin4: Left[3]
Taito 6 Pin
Pin1: +5 Volts
Pin2: +5 Volts
Pin3: GND
Pin4: GND
Pin5: Left
Pin6: Right[4]
Ultimarc to USB Interface
Pin1: +5 Volts (Brown)
Pin2: X2 (Green)
Pin3: GND (White)
Pin4: X1 (Yellow)
Pin5: Empty[5]